Skip to main content

Category: Modem & Router Setup · Last updated 16 Nov 2026

Setting up your TP-Link VX230v

How to set up a TP-Link VX230v on FTTN/FTTB or Ethernet WAN nbn, extend its Wi-Fi with Aginet mesh, and use bridge mode.

The TP-Link VX230v is a Wi-Fi 6 modem router from TP-Link's Aginet range, with a built-in VDSL modem, so it works on every nbn technology type.

Bought your VX230v from Lightning IP? It arrives pre-configured for your service. Just connect it to your nbn equipment (or your phone socket on FTTN or FTTB) and switch it on. You don't need to follow the setup steps below.

Use this guide if your VX230v came from another provider, was bought in a shop, or has been factory reset. If it came from another provider, factory reset it before you start by holding the Reset button for about 10 seconds. As an Aginet device, you can also manage it from the TP-Link Aginet app once it's online.

Before you start

Check which nbn technology your address uses, then follow the matching section below. Whichever section you use, these are the settings our network needs:

SettingWhat to choose
Connection typeDynamic IP (sometimes called IPoE, DHCP or Automatic)
VLAN / VLAN IDOff (untagged)
Username and passwordNot needed

If your modem is already set up for PPPoE from a previous provider, you can leave it that way. We accept PPPoE with any username and password. Just make sure the VLAN setting is turned off.

Logging in to your VX230v

  1. Connect a device Join the modem's Wi-Fi using the name and password on the label underneath, or plug a computer into one of the LAN ports with an ethernet cable.
  2. Open the setup page In a web browser, go to http://tplinkmodem.net or 192.168.1.1.
  3. Sign in On first use you'll be asked to create an admin password. If the modem was supplied by another provider, the password may be printed on the label.

Setting up on FTTN or FTTB

  1. Connect to the phone socket Plug the phone cable into the grey DSL port on the modem and the other end into your wall phone socket. Use the socket nbn activated (usually the main socket) and don't use any line filters or splitters.
  2. Power on and log in Switch the modem on, then log in as described above.
  3. Start Quick Setup Quick Setup opens automatically on a new or reset modem. Otherwise, click Quick Setup at the top of the page.
  4. Set your region Choose Australia and your time zone, then click Next.
  5. Choose your provider Select Other from the ISP list, then click Next.
  6. Enter the internet settings Tick VDSL. Leave the VLAN ID box unticked. Set the connection type to Dynamic IP, then click Next.
  7. Finish setup Set your Wi-Fi name and password if you'd like to change them, then save. Allow up to 10 minutes for the DSL light to go solid, followed by the Internet light.

Setting up on FTTP, HFC, FTTC or Fixed Wireless

On these technologies the VX230v connects to your nbn equipment with an ethernet cable (called Ethernet WAN).

  1. Connect to your nbn equipment Run an ethernet cable from the modem's ethernet WAN port (labelled LAN4/WAN on some units) to your nbn equipment: port UNI-D1 on an FTTP or Fixed Wireless Connection Box, the ethernet port on an HFC Connection Box, or the port labelled Gateway on an FTTC Connection Device.
  2. Power on and log in Switch the modem on, then log in as described above.
  3. Start Quick Setup Click Quick Setup if it doesn't open automatically, and set your region to Australia.
  4. Choose your provider Select Other from the ISP list.
  5. Enter the internet settings Leave VDSL unticked so the modem uses its ethernet WAN port. Leave VLAN ID unticked and set the connection type to Dynamic IP. If you're asked for an operation mode instead, choose Wireless Router Mode.
  6. Finish setup Save your Wi-Fi settings and wait a few minutes for the Internet light to turn on.

Extending your Wi-Fi with Aginet mesh

If the VX230v's Wi-Fi doesn't reach every room, you can add TP-Link Aginet mesh units (the HX510, HX716 Pro or HB210 Pro). They join the VX230v to create one Wi-Fi network across your home, with the same name and password everywhere. This works on every nbn technology, including FTTN and FTTB, and the VX230v stays in charge of your connection, so you don't need bridge mode.

  1. Make sure the VX230v is online Set it up using the steps above and check the Internet light is on.
  2. Open the Aginet app Join your phone to the VX230v's Wi-Fi, open the TP-Link Aginet app and log in. The app will find your VX230v; if it's the first time, set a device password.
  3. Add a mesh unit Tap + and choose to add a mesh device, then select your model.
  4. Power on the mesh unit Place the mesh unit near the VX230v for setup, plug it into power and wait until the light flashes blue. Follow the prompts in the app to pair it.
  5. Move it into place Once paired, move the mesh unit to where you need better coverage, ideally within one or two rooms of the VX230v. Its light should turn solid when it has a good connection.
  6. Add any extra units Repeat for each extra mesh unit.

For the fastest, most reliable connection, run an ethernet cable from a LAN port on the VX230v to the WAN/LAN port on the mesh unit. See our Aginet mesh setup guide for more detail.

Using bridge mode with your own router (FTTN and FTTB)

If you're on FTTN or FTTB and want to use a different brand of router or mesh system (such as eero or Deco), you can set the VX230v to bridge mode. It then acts only as a VDSL modem and your own router handles the connection and Wi-Fi. If you just want better coverage, adding Aginet mesh (above) is simpler.

Bridge mode is only needed on FTTN and FTTB. On FTTP, HFC, FTTC and Fixed Wireless, plug your own router straight into the nbn equipment instead and you don't need the VX230v at all.

  1. Connect with a cable Plug a computer into a LAN port on the VX230v and log in.
  2. Open the internet settings Go to Advanced > Network > Internet.
  3. Remove the current connection Delete the existing VDSL internet connection using the bin icon.
  4. Add a bridge connection Click Add. Set DSL Modulation Type to VDSL and Internet Connection Type to Bridge. Leave VLAN turned off, then click Save.
  5. Connect your router Run an ethernet cable from a LAN port on the VX230v to the WAN (internet) port on your own router.
  6. Set up your router Set your router's internet connection type to Dynamic IP with VLAN turned off. See our guide for your router for the exact steps.
  7. Turn off the modem's Wi-Fi (optional) Press the Wi-Fi button on the VX230v so its Wi-Fi doesn't compete with your router's.

Once bridge mode is on, the VX230v's setup page may no longer be reachable from your router's network, and Aginet mesh units can't pair with it. To go back to using it as a normal modem router, factory reset it and follow the FTTN or FTTB steps above.

If it doesn't connect

  • DSL light flashing or off (FTTN/FTTB) - Check the phone cable is firmly connected, remove any filters or splitters, and try another phone socket if you have one.
  • Internet light off - Log back in and check the connection type is Dynamic IP and that VLAN is turned off.
  • Mesh unit won't pair - Move it closer to the VX230v, make sure the VX230v is online and not in bridge mode, and try adding it again in the Aginet app.
  • Still no luck - Restart the modem properly and follow our no internet connection troubleshooting guide, or get in touch and we'll check your service.

Related Articles

Was this article helpful?

Your feedback helps us improve our support content.