Category: Modem & Router Setup · Last updated 16 Nov 2026
Setting up your TP-Link Aginet mesh Wi-Fi (HX510, HX716 Pro or HB210 Pro)
How to set up a TP-Link Aginet mesh Wi-Fi system (HX510, HX716 Pro or HB210 Pro) on your nbn connection, including pairing it with a VX230v or VX420-G2h on FTTN/FTTB.
TP-Link's Aginet mesh Wi-Fi systems, including the HX510, HX716 Pro and HB210 Pro, are all set up the same way through the TP-Link Aginet app.
Bought your Aginet mesh from Lightning IP? It arrives pre-configured for your service. Just connect the main unit to your nbn equipment and switch it on. You don't need to follow the setup steps below.
Which setup do you need?
These Aginet mesh units don't have a VDSL modem built in, so how you set them up depends on your nbn technology:
- FTTP, HFC, FTTC or Fixed Wireless - The main mesh unit plugs straight into your nbn equipment. Follow Setting up your Aginet mesh below.
- FTTN or FTTB - Pair your mesh units with a TP-Link VX230v or VX420-G2h modem router. The modem connects to your phone socket, and the mesh units extend its Wi-Fi around your home as one network. Follow Using Aginet mesh on FTTN or FTTB below.
Before you start
| Setting | What to choose |
|---|---|
| Connection type | Dynamic IP (sometimes called IPoE or DHCP) |
| VLAN | Off |
| Username and password | Not needed |
You'll also need the TP-Link Aginet app on your phone (App Store or Google Play).
If your Aginet mesh came from another provider, factory reset it before you start. Hold the Reset button on the back for about 10 seconds until the light changes, then wait two minutes for it to restart. This clears any settings your previous provider added.
Setting up your Aginet mesh
Use these steps on FTTP, HFC, FTTC or Fixed Wireless.
- Connect the main unit Run an ethernet cable from the WAN/LAN port on your main unit to your nbn equipment: port UNI-D1 on an FTTP or Fixed Wireless Connection Box, the ethernet port on an HFC Connection Box, or the port labelled Gateway on an FTTC Connection Device.
- Power it on Plug the unit into power and wait about two minutes, until the light flashes blue.
- Open the Aginet app Log in with your TP-Link ID, or tap Continue without TP-Link ID. On iPhone, allow the app to access your local network when asked.
- Connect to the mesh Join your phone to the Wi-Fi network printed on the label under the unit. The app will find the device; tap Set up device.
- Set a device password Create a password for managing the mesh. Keep it somewhere safe.
- Choose the internet settings When asked how you connect, choose Dynamic IP (it's often detected automatically) and leave VLAN turned off.
- Name your network Choose a Wi-Fi name and password, and leave band steering on.
- Add more units If you have a multi-pack, tap + in the app to add each extra unit. Place them within one or two rooms of each other, or connect them with ethernet for the best performance.
Using Aginet mesh on FTTN or FTTB
On FTTN or FTTB, your TP-Link VX230v or VX420-G2h is the main device. It connects to your phone socket and runs your network, and your HX510, HX716 Pro or HB210 Pro units join it as mesh points.
- Set up your modem first Make sure your VX230v or VX420-G2h is connected and online. If you need help, see our setup guide for your modem.
- Open the Aginet app Join your phone to your modem's Wi-Fi, open the Aginet app and log in. The app will find your modem; if it's the first time, set a device password.
- Add a mesh unit Tap + and choose to add a mesh device, then select your model (HX510, HX716 Pro or HB210 Pro).
- Power on the mesh unit Place the mesh unit near the modem for setup, plug it into power and wait until the light flashes blue. Follow the prompts in the app to pair it.
- Move it into place Once paired, move the mesh unit to where you need better coverage, ideally within one or two rooms of the modem. Its light should turn solid when it has a good connection.
- Add any extra units Repeat for each extra mesh unit.
For the fastest, most reliable connection between units, you can run an ethernet cable from a LAN port on the modem to the WAN/LAN port on a mesh unit. Don't set the modem to bridge mode for this setup, because it needs to stay in charge of your network.
Setting up with a web browser instead
If you'd rather not use the app on FTTP, HFC, FTTC or Fixed Wireless, connect a computer to the main unit's Wi-Fi or a LAN port and go to http://tplinkwifi.net. Create a login password, then set the internet connection type to Dynamic IP with VLAN turned off.
If it doesn't connect
- Light stays red or the app can't find the internet - Check the cable is in the WAN/LAN port and the correct port on your nbn equipment, then power-cycle the nbn equipment and the mesh.
- Mesh unit won't pair on FTTN or FTTB - Move it closer to the modem, make sure the modem is online, and try adding it again in the Aginet app.
- Still no luck - The Aginet app has built-in troubleshooting. You can also follow our no internet connection troubleshooting guide, or get in touch.
Related Articles
- Modem & Router SetupModem and router setup guides: find your deviceFind the setup guide for your modem, router or mesh Wi-Fi system, and the settings our network needs.
- Modem & Router SetupSetting up a Telstra Smart ModemHow to factory reset and connect a Telstra Smart Modem to your Lightning IP nbn service, and how to use bridge mode.
- Modem & Router SetupSetting up an Optus Ultra WiFi ModemHow to factory reset and connect an Optus Ultra WiFi Modem to your Lightning IP nbn service.
- Modem & Router SetupSetting up an older NetComm modem (NF18ACV, NF17ACV or NF10WV)How to set up an older NetComm NF18ACV, NF17ACV or NF10WV on FTTN/FTTB or Ethernet WAN nbn, and how to put it in bridge mode.
Was this article helpful?
Your feedback helps us improve our support content.