Category: Modem & Router Setup · Last updated 16 Nov 2026
Setting up your TP-Link Archer router
How to set up a TP-Link Archer Wi-Fi router (such as the AX55, AX73, C6 or C7) on your nbn connection.
TP-Link Archer Wi-Fi routers, such as the Archer AX55, AX73, AX10, C6 and C7, share very similar setup screens. This guide covers Archer models without a phone socket port. If your Archer model name starts with VR or VX, it has a built-in modem, so see our Archer VR-series or VX-series guides instead.
Archer routers don't have a VDSL modem built in. On FTTP, HFC, FTTC and Fixed Wireless they plug straight into your nbn equipment. On FTTN or FTTB you'll also need a VDSL modem set to bridge mode, with the Archer plugged into it. See our modem and router setup guides for how to set up bridge mode on your modem.
Before you start
| Setting | What to choose |
|---|---|
| Connection type | Dynamic IP |
| VLAN (IPTV/VLAN) | Off |
| Username and password | Not needed |
Setting up your Archer router
- Connect to your nbn equipment Run an ethernet cable from the router's WAN or Internet port (usually a different colour to the others) to your nbn equipment: port UNI-D1 on an FTTP or Fixed Wireless Connection Box, the ethernet port on an HFC Connection Box, or the port labelled Gateway on an FTTC Connection Device. On FTTN or FTTB, plug it into a LAN port on your bridged VDSL modem instead.
- Power on and connect a device Switch the router on and join its Wi-Fi using the details on the label, or plug a computer into a LAN port.
- Open the setup page In a web browser, go to http://tplinkwifi.net or 192.168.0.1, and create an admin password. You can also use the TP-Link Tether app.
- Run Quick Setup Choose your time zone, then set the connection type to Dynamic IP (or use Auto Detect).
- Skip the MAC address step If asked, choose Do NOT clone MAC address.
- Set up Wi-Fi Choose your Wi-Fi name and password, then save. Wait a few minutes for the connection to come up.
Checking the VLAN setting
If your router was set up by another provider, a VLAN may be turned on, which will stop it connecting to our network.
- Open the VLAN settings Log in and go to Advanced > Network > IPTV/VLAN.
- Turn it off Untick IPTV/VLAN (or turn the switch off) and click Save.
- Check the internet settings Go to Advanced > Network > Internet and make sure the connection type is Dynamic IP. PPPoE also works on our network with any username and password.
If it doesn't connect
- Internet light off or orange - Check the cable is in the router's WAN port and the correct port on your nbn equipment, then power-cycle the nbn equipment and the router.
- On FTTN or FTTB - Make sure your VDSL modem is in bridge mode and its DSL light is solid.
- Still no luck - Follow our no internet connection troubleshooting guide, or get in touch.
Related Articles
- Modem & Router SetupModem and router setup guides: find your deviceFind the setup guide for your modem, router or mesh Wi-Fi system, and the settings our network needs.
- Modem & Router SetupSetting up a Telstra Smart ModemHow to factory reset and connect a Telstra Smart Modem to your Lightning IP nbn service, and how to use bridge mode.
- Modem & Router SetupSetting up an Optus Ultra WiFi ModemHow to factory reset and connect an Optus Ultra WiFi Modem to your Lightning IP nbn service.
- Modem & Router SetupSetting up an older NetComm modem (NF18ACV, NF17ACV or NF10WV)How to set up an older NetComm NF18ACV, NF17ACV or NF10WV on FTTN/FTTB or Ethernet WAN nbn, and how to put it in bridge mode.
Was this article helpful?
Your feedback helps us improve our support content.