Skip to main content

Category: Modem & Router Setup · Last updated 16 Nov 2026

Setting up your NetComm NF20MESH

How to set up a NetComm NF20MESH on FTTN/FTTB or Ethernet WAN nbn, and how to put it in bridge mode.

The NetComm NF20MESH (CloudMesh Gateway) is a Wi-Fi 6 modem router with a built-in VDSL modem, so it works on every nbn technology type. If you bought it from Lightning IP, it arrives pre-configured and you only need to plug it in. Use this guide if yours came from another provider (it's commonly supplied by Aussie Broadband), or has been factory reset.

Before you start

Check which nbn technology your address uses, then follow the matching section below. These are the settings our network needs:

SettingWhat to choose
Connection typeDynamic IP (sometimes called IPoE, DHCP or Automatic)
VLAN / VLAN IDOff (untagged), or leave the VLAN field blank
Username and passwordNot needed

If your modem is already set up for PPPoE from a previous provider, you can leave it that way. We accept PPPoE with any username and password. Just make sure the VLAN setting is turned off.

Logging in to your NF20MESH

  1. Connect a device Join the modem's Wi-Fi using the WiFi Network Name and WiFi Password on the label underneath, or plug a computer into a yellow LAN port. Your device may say it has no internet at this stage; that's normal.
  2. Open the setup page In a web browser, go to 192.168.20.1.
  3. Sign in Enter admin as the username. The password is printed on the label under Gateway Login Page. It's different from the Wi-Fi password.

Setting up on FTTN or FTTB

  1. Connect to the phone socket Plug the phone cable into the grey DSL port on the modem and the other end into your wall phone socket. Don't use any line filters or splitters.
  2. Power on and log in Press the power button, wait a few minutes for it to start up, then log in as described above.
  3. Run the wizard Select Run Quick Start Wizard.
  4. Choose the internet service Set Internet Service to VDSL.
  5. Choose the connection type Set Connection Type to Dynamic IP (or IPoE). Leave the VLAN field blank or turned off.
  6. Finish the wizard Click Next through the remaining screens, set your time zone, then click Finish. Allow up to 10 minutes for the DSL light to go solid, followed by the Internet light.

Setting up on FTTP, HFC, FTTC or Fixed Wireless

  1. Connect to your nbn equipment Run an ethernet cable from the modem's WAN port to your nbn equipment: port UNI-D1 on an FTTP or Fixed Wireless Connection Box, the ethernet port on an HFC Connection Box, or the port labelled Gateway on an FTTC Connection Device.
  2. Power on and log in Press the power button, wait a few minutes, then log in as described above.
  3. Run the wizard Select Run Quick Start Wizard.
  4. Choose the internet service Set Internet Service to Ethernet WAN.
  5. Choose the connection type Set Connection Type to Dynamic IP (or IPoE). Leave the VLAN field blank or turned off.
  6. Finish the wizard Click Next through the remaining screens, set your time zone, then click Finish. The Internet light should turn on within a few minutes.

Using bridge mode with your own router (FTTN and FTTB)

On FTTN or FTTB you can set the NF20MESH to bridge mode so it acts only as a VDSL modem, and your own router or mesh system handles the connection and Wi-Fi.

Bridge mode is only needed on FTTN and FTTB. On other technologies, plug your own router straight into the nbn equipment instead.

On the NF20MESH, simply choosing a bridge option in the wizard often doesn't fully take effect. Follow all of the steps below, in order, and use an ethernet cable rather than Wi-Fi, because you'll turn Wi-Fi off along the way.

  1. Connect with a cable Plug a computer into a yellow LAN port and log in.
  2. Remove the existing internet connections In the internet (WAN) connection settings under Advanced, delete every existing internet connection, including any VDSL (PTM) and Ethernet WAN connections.
  3. Add a VDSL bridge connection Add a new VDSL (PTM) connection and set its connection type to Bridge. Leave VLAN turned off and save.
  4. Turn off Wi-Fi In the Wi-Fi settings, turn off the 2.4 GHz and 5 GHz networks and stop the network names being broadcast.
  5. Turn off DHCP In the LAN settings, turn off the DHCP server for both IPv4 and IPv6, then save. Do this last, because you'll lose access to the setup page afterwards.
  6. Connect your router Run an ethernet cable from a yellow LAN port on the NF20MESH to the WAN (internet) port on your own router.
  7. Set up your router Set your router's internet connection type to Dynamic IP with VLAN turned off.

To undo bridge mode, factory reset the NF20MESH by holding the reset button for about 10 seconds, then follow the FTTN or FTTB steps above.

If it doesn't connect

  • DSL light flashing or off (FTTN/FTTB) - Check the phone cable, remove any filters or splitters, and try another phone socket.
  • Internet light off - Check the internet service matches your technology (VDSL or Ethernet WAN), the connection type is Dynamic IP, and VLAN is turned off.
  • Still no luck - Restart the modem properly and follow our no internet connection troubleshooting guide, or get in touch.

Related Articles

Was this article helpful?

Your feedback helps us improve our support content.