---
title: "Setting up your NetComm NF20MESH"
description: "How to set up a NetComm NF20MESH on FTTN/FTTB or Ethernet WAN nbn, and how to put it in bridge mode."
url: "https://www.lightningip.com.au/help/internet/setup-netcomm-nf20mesh"
canonical: "https://www.lightningip.com.au/help/internet/setup-netcomm-nf20mesh"
updated: "2026-11-16"
---

# Setting up your NetComm NF20MESH

How to set up a NetComm NF20MESH on FTTN/FTTB or Ethernet WAN nbn, and how to put it in bridge mode.

The NetComm NF20MESH (CloudMesh Gateway) is a Wi-Fi 6 modem router with a built-in VDSL modem, so it works on every nbn technology type. If you bought it from Lightning IP, it arrives pre-configured and you only need to plug it in. Use this guide if yours came from another provider (it's commonly supplied by Aussie Broadband), or has been factory reset.

## Before you start

Check which nbn technology your address uses, then follow the matching section below. These are the settings our network needs:

| Setting | What to choose |
|---|---|
| Connection type | Dynamic IP (sometimes called IPoE, DHCP or Automatic) |
| VLAN / VLAN ID | Off (untagged), or leave the VLAN field blank |
| Username and password | Not needed |

If your modem is already set up for PPPoE from a previous provider, you can leave it that way. We accept PPPoE with any username and password. Just make sure the VLAN setting is turned off.

## Logging in to your NF20MESH

1. **Connect a device** - Join the modem's Wi-Fi using the **WiFi Network Name** and **WiFi Password** on the label underneath, or plug a computer into a yellow LAN port. Your device may say it has no internet at this stage; that's normal.
2. **Open the setup page** - In a web browser, go to **192.168.20.1**.
3. **Sign in** - Enter **admin** as the username. The password is printed on the label under **Gateway Login Page**. It's different from the Wi-Fi password.

## Setting up on FTTN or FTTB

1. **Connect to the phone socket** - Plug the phone cable into the grey **DSL** port on the modem and the other end into your wall phone socket. Don't use any line filters or splitters.
2. **Power on and log in** - Press the power button, wait a few minutes for it to start up, then log in as described above.
3. **Run the wizard** - Select **Run Quick Start Wizard**.
4. **Choose the internet service** - Set **Internet Service** to **VDSL**.
5. **Choose the connection type** - Set **Connection Type** to **Dynamic IP** (or **IPoE**). Leave the **VLAN** field blank or turned off.
6. **Finish the wizard** - Click **Next** through the remaining screens, set your time zone, then click **Finish**. Allow up to 10 minutes for the **DSL** light to go solid, followed by the **Internet** light.

## Setting up on FTTP, HFC, FTTC or Fixed Wireless

1. **Connect to your nbn equipment** - Run an ethernet cable from the modem's **WAN** port to your nbn equipment: port **UNI-D1** on an FTTP or Fixed Wireless Connection Box, the ethernet port on an HFC Connection Box, or the port labelled **Gateway** on an FTTC Connection Device.
2. **Power on and log in** - Press the power button, wait a few minutes, then log in as described above.
3. **Run the wizard** - Select **Run Quick Start Wizard**.
4. **Choose the internet service** - Set **Internet Service** to **Ethernet WAN**.
5. **Choose the connection type** - Set **Connection Type** to **Dynamic IP** (or **IPoE**). Leave the **VLAN** field blank or turned off.
6. **Finish the wizard** - Click **Next** through the remaining screens, set your time zone, then click **Finish**. The **Internet** light should turn on within a few minutes.

## Using bridge mode with your own router (FTTN and FTTB)

On FTTN or FTTB you can set the NF20MESH to bridge mode so it acts only as a VDSL modem, and your own router or mesh system handles the connection and Wi-Fi.

Bridge mode is only needed on FTTN and FTTB. On other technologies, plug your own router straight into the nbn equipment instead.

On the NF20MESH, simply choosing a bridge option in the wizard often doesn't fully take effect. Follow all of the steps below, in order, and use an ethernet cable rather than Wi-Fi, because you'll turn Wi-Fi off along the way.

1. **Connect with a cable** - Plug a computer into a yellow LAN port and log in.
2. **Remove the existing internet connections** - In the internet (WAN) connection settings under **Advanced**, delete every existing internet connection, including any VDSL (PTM) and Ethernet WAN connections.
3. **Add a VDSL bridge connection** - Add a new VDSL (PTM) connection and set its connection type to **Bridge**. Leave VLAN turned off and save.
4. **Turn off Wi-Fi** - In the Wi-Fi settings, turn off the 2.4 GHz and 5 GHz networks and stop the network names being broadcast.
5. **Turn off DHCP** - In the LAN settings, turn off the **DHCP server** for both IPv4 and IPv6, then save. Do this last, because you'll lose access to the setup page afterwards.
6. **Connect your router** - Run an ethernet cable from a yellow LAN port on the NF20MESH to the WAN (internet) port on your own router.
7. **Set up your router** - Set your router's internet connection type to **Dynamic IP** with VLAN turned off.

To undo bridge mode, factory reset the NF20MESH by holding the reset button for about 10 seconds, then follow the FTTN or FTTB steps above.

## If it doesn't connect

- **DSL light flashing or off (FTTN/FTTB)** - Check the phone cable, remove any filters or splitters, and try another phone socket.
- **Internet light off** - Check the internet service matches your technology (VDSL or Ethernet WAN), the connection type is **Dynamic IP**, and VLAN is turned off.
- **Still no luck** - Restart the modem properly and follow our no internet connection troubleshooting guide, or get in touch.
