Skip to main content

Category: Modem & Router Setup · Last updated 16 Nov 2026

Setting up your TP-Link VB433v

How to set up a TP-Link VB433v Wi-Fi 7 modem on FTTN/FTTB or Ethernet WAN nbn, and how to put it in bridge mode.

The TP-Link VB433v is a Wi-Fi 7 modem router with a built-in VDSL modem and a 2.5 Gbps ethernet WAN port, so it works on every nbn technology type. Use this guide if your VB433v came from another provider (it's commonly supplied by Superloop and Leaptel), was bought in a shop, or has been factory reset.

Before you start

Check which nbn technology your address uses, then follow the matching section below. These are the settings our network needs:

SettingWhat to choose
Connection typeDynamic IP (sometimes called IPoE, DHCP or Automatic)
VLAN / VLAN IDOff (untagged)
Username and passwordNot needed

If your modem is already set up for PPPoE from a previous provider, you can leave it that way. We accept PPPoE with any username and password. Just make sure the VLAN setting is turned off.

Logging in to your VB433v

  1. Connect a device Join the modem's Wi-Fi using the details on the label underneath, or plug a computer into one of the LAN ports.
  2. Open the setup page In a web browser, go to http://tplinkmodem.net or 192.168.1.1.
  3. Sign in Create an admin password when prompted, or use the password on the label if your previous provider set one.

Setting up on FTTN or FTTB

  1. Connect to the phone socket Plug the phone cable into the DSL port on the modem and the other end into your wall phone socket. Use the socket nbn activated and don't use any line filters or splitters.
  2. Power on and log in Switch the modem on and log in as described above.
  3. Start Quick Setup Quick Setup opens automatically on a new or reset modem. Otherwise, click Quick Setup.
  4. Set your region Choose Australia and your time zone.
  5. Choose your provider Select Other from the ISP list.
  6. Enter the internet settings Choose VDSL as the connection. Leave VLAN ID turned off and set the connection type to Dynamic IP.
  7. Finish setup Save your Wi-Fi settings. Allow up to 10 minutes for the DSL light to go solid, followed by the Internet light.

Setting up on FTTP, HFC, FTTC or Fixed Wireless

  1. Connect to your nbn equipment Run an ethernet cable from the modem's 2.5 Gbps WAN port to your nbn equipment: port UNI-D1 on an FTTP or Fixed Wireless Connection Box, the ethernet port on an HFC Connection Box, or the port labelled Gateway on an FTTC Connection Device.
  2. Power on and log in Switch the modem on and log in as described above.
  3. Run Quick Setup Set your region to Australia and choose Other from the ISP list.
  4. Enter the internet settings Choose Ethernet WAN (not VDSL) as the connection. Leave VLAN ID turned off and set the connection type to Dynamic IP.
  5. Finish setup Save your Wi-Fi settings and wait a few minutes for the Internet light to turn on.

On FTTN and FTTB the VB433v's VDSL modem tops out at around 300 Mbps, which is above what those connections deliver. On FTTP and HFC, its 2.5 Gbps WAN port can handle our fastest plans.

Using bridge mode with your own router (FTTN and FTTB)

On FTTN or FTTB you can set the VB433v to bridge mode so it acts only as a VDSL modem, and your own router or mesh system handles the connection and Wi-Fi.

Bridge mode is only needed on FTTN and FTTB. On other technologies, plug your own router straight into the nbn equipment instead.

  1. Connect with a cable Plug a computer into a LAN port on the VB433v and log in.
  2. Open the internet settings Go to Advanced > Network > Internet.
  3. Remove the current connection Delete the existing VDSL internet connection.
  4. Add a bridge connection Click Add. Set DSL Modulation Type to VDSL and Internet Connection Type to Bridge. Leave VLAN turned off, then click Save.
  5. Connect your router Run an ethernet cable from a LAN port on the VB433v to the WAN (internet) port on your own router.
  6. Set up your router Set your router's internet connection type to Dynamic IP with VLAN turned off.
  7. Turn off the modem's Wi-Fi (optional) Press the Wi-Fi button on the VB433v so it doesn't compete with your router's Wi-Fi.

Once bridge mode is on, the VB433v's setup page may no longer be reachable from your router's network. To undo it, factory reset the modem and follow the FTTN or FTTB steps above.

If it doesn't connect

  • DSL light flashing or off (FTTN/FTTB) - Check the phone cable, remove any filters or splitters, and try another phone socket.
  • Internet light off - Check the connection type is Dynamic IP and that VLAN is turned off.
  • Still no luck - Restart the modem properly and follow our no internet connection troubleshooting guide, or get in touch.

Related Articles

Was this article helpful?

Your feedback helps us improve our support content.