Category: Modem & Router Setup · Last updated 16 Nov 2026
Setting up your TP-Link Deco mesh Wi-Fi
How to set up a TP-Link Deco mesh system (X50, X55, M4, M5, BE63 and others) on your nbn connection, including the Deco X20-DSL.
TP-Link Deco mesh systems, including the Deco X50, X55, M4, M5, S4 and BE63, are all set up the same way through the Deco app. If you bought your Deco from Lightning IP, just follow the app and it will connect automatically.
Most Deco models are routers, not modems, so they don't have a VDSL modem built in. On FTTP, HFC, FTTC and Fixed Wireless they plug straight into your nbn equipment. On FTTN or FTTB you'll also need a VDSL modem set to bridge mode, with the Deco plugged into it. See our modem and router setup guides for how to set up bridge mode on your modem. The exception is the Deco X20-DSL, which has a modem built in (see below).
Before you start
| Setting | What to choose |
|---|---|
| Connection type | Dynamic IP |
| VLAN (IPTV/VLAN) | Off |
| Username and password | Not needed |
You'll also need the Deco app on your phone (App Store or Google Play) and a TP-Link ID.
Setting up your Deco
- Connect your main Deco Run an ethernet cable from either ethernet port on one Deco to your nbn equipment: port UNI-D1 on an FTTP or Fixed Wireless Connection Box, the ethernet port on an HFC Connection Box, or the port labelled Gateway on an FTTC Connection Device. On FTTN or FTTB, plug it into a LAN port on your bridged VDSL modem instead.
- Power it on Plug the Deco into power and wait for the light to pulse blue.
- Open the Deco app Sign in with your TP-Link ID, tap Set up a new device and choose your Deco model.
- Choose the connection type When the app asks for your internet connection type, choose Dynamic IP. It often detects this automatically.
- Name your network Choose a Wi-Fi name and password.
- Add more Decos If you have a multi-pack, tap + to add each extra Deco. Place them within one or two rooms of each other for the best connection between units.
If your Deco was set up by another provider
- Open the settings In the Deco app, tap More > Advanced.
- Check the IPv4 settings Tap IPv4 and make sure the connection type is Dynamic IP. PPPoE also works on our network with any username and password.
- Turn off VLAN Go back to Advanced, tap IPTV/VLAN and make sure it's turned off.
- Save and wait Save your changes and give the Deco a couple of minutes to reconnect.
Deco X20-DSL on FTTN or FTTB
The Deco X20-DSL has a VDSL modem built into the main unit, so on FTTN or FTTB you don't need a separate modem.
- Connect to the phone socket Plug the phone cable into the DSL port on the main Deco X20-DSL and the other end into your wall phone socket. Don't use any line filters or splitters.
- Start setup in the Deco app Choose Deco X20-DSL as your model and follow the prompts.
- Choose the connection When asked, choose VDSL and Dynamic IP. Leave VLAN turned off.
- Finish setup Name your network and add any extra Decos. Allow up to 10 minutes for the line to connect.
On FTTP, HFC, FTTC or Fixed Wireless, the Deco X20-DSL connects with an ethernet cable like any other Deco. Follow the main steps above and choose Ethernet rather than DSL when the app asks.
If it doesn't connect
- Light stays red - Check the cable is plugged into the correct port on your nbn equipment, and power-cycle the nbn equipment and the Deco.
- On FTTN or FTTB - Make sure your VDSL modem is in bridge mode and its DSL light is solid.
- Still no luck - Follow our no internet connection troubleshooting guide, or get in touch.
Related Articles
- Modem & Router SetupModem and router setup guides: find your deviceFind the setup guide for your modem, router or mesh Wi-Fi system, and the settings our network needs.
- Modem & Router SetupSetting up a Telstra Smart ModemHow to factory reset and connect a Telstra Smart Modem to your Lightning IP nbn service, and how to use bridge mode.
- Modem & Router SetupSetting up an Optus Ultra WiFi ModemHow to factory reset and connect an Optus Ultra WiFi Modem to your Lightning IP nbn service.
- Modem & Router SetupSetting up an older NetComm modem (NF18ACV, NF17ACV or NF10WV)How to set up an older NetComm NF18ACV, NF17ACV or NF10WV on FTTN/FTTB or Ethernet WAN nbn, and how to put it in bridge mode.
Was this article helpful?
Your feedback helps us improve our support content.