Category: Modem & Router Setup · Last updated 19 Nov 2026
Setting up your NetComm NF18MESH
How to set up a NetComm NF18MESH modem on FTTN, FTTB, Fixed Wireless and other nbn connections with Lightning IP.
The NetComm NF18MESH is a modem router with a built-in VDSL modem, so it works on every nbn technology type. If you bought it from Lightning IP, it arrives set up and you only need to plug it in. Use this guide if yours came from another provider or has been factory reset.
Before you start
Check which nbn technology your address uses, then follow the matching section below. These are the settings our network needs:
| Setting | What to choose |
|---|---|
| Connection type | Dynamic IP (sometimes called IPoE, DHCP or Automatic) |
| VLAN / VLAN ID | Off (untagged), or leave the VLAN field blank |
| Username and password | Not needed |
If the modem came from another provider, start with a factory reset. With the modem switched on, hold the Reset button with a paperclip for about 10 seconds, then let it restart.
Logging in to your NF18MESH
- Connect a device Plug a computer into a yellow LAN port with an ethernet cable, or join the modem's Wi-Fi using the details on the label.
- Open the setup page In a web browser, go to 192.168.20.1 (or http://cloudmesh.home).
- Sign in Enter the username and password printed on the label on the back of the modem.
Setting up on FTTN or FTTB
- Connect to the phone socket Plug the phone cable into the grey DSL port (the far-left port) and the other end into your wall phone socket. Don't use any line filters or splitters.
- Power on Plug in the power cable and press the Power button on the side. Allow 2 to 3 minutes for it to start up.
- Log in Log in as described above, then click Yes, start the setup wizard.
- Choose the service Select VDSL.
- Choose the connection type Select Dynamic IP, leave VLAN turned off, and click Next.
- Set up your Wi-Fi Choose your own Wi-Fi name and password if you like, then click Next.
- Finish Leave the other settings as they are and click Next through to the summary page. Allow up to 10 minutes for the DSL light to go solid, followed by the Internet light.
Setting up on Fixed Wireless, FTTP, HFC or FTTC
- Connect to your nbn equipment Run an ethernet cable from the blue WAN port on the modem to your nbn equipment: the UNI-D port we gave you when your order was completed on a Fixed Wireless or FTTP Connection Box, the ethernet port on an HFC Connection Box, or the port labelled Gateway on an FTTC Connection Device.
- Power on Plug in the power cable and press the Power button on the side. Allow 2 to 3 minutes for it to start up.
- Check the connection The Internet light should turn green (solid or flashing) within a few minutes.
- If it doesn't connect Log in, start the setup wizard, choose Ethernet WAN and set the connection type to Dynamic IP with VLAN turned off.
Want to use the phone port?
If you have a Lightning IP Voice Line, you can plug a home phone into the NF18MESH. See Setting up your Voice Line on a NetComm NF18MESH.
If it doesn't connect
- DSL light flashing or off (FTTN/FTTB) - Check the phone cable, remove any filters or splitters, and try another phone socket.
- Internet light off - Check the connection type is Dynamic IP and VLAN is turned off. On Fixed Wireless, FTTP, HFC or FTTC, check the cable is in the blue WAN port.
- Still no luck - Restart your modem properly and follow our no internet connection guide, or get in touch.
Related Articles
- Modem & Router SetupModem and router setup guides: find your deviceFind the setup guide for your modem, router or mesh Wi-Fi system, and the settings our network needs.
- Modem & Router SetupSetting up a Telstra Smart ModemHow to factory reset and connect a Telstra Smart Modem to your Lightning IP nbn service, and how to use bridge mode.
- Modem & Router SetupSetting up an Optus Ultra WiFi ModemHow to factory reset and connect an Optus Ultra WiFi Modem to your Lightning IP nbn service.
- Modem & Router SetupSetting up an older NetComm modem (NF18ACV, NF17ACV or NF10WV)How to set up an older NetComm NF18ACV, NF17ACV or NF10WV on FTTN/FTTB or Ethernet WAN nbn, and how to put it in bridge mode.
Was this article helpful?
Your feedback helps us improve our support content.