---
title: "Setting up your TP-Link VX420-G2h or VX420-G2v"
description: "How to set up the TP-Link VX420-G2h small business modem (with optional 4G backup) on any nbn technology, extend its Wi-Fi with Aginet mesh, and use bridge mode."
url: "https://www.lightningip.com.au/help/internet/setup-tp-link-vx420-g2"
canonical: "https://www.lightningip.com.au/help/internet/setup-tp-link-vx420-g2"
updated: "2026-11-16"
---

# Setting up your TP-Link VX420-G2h or VX420-G2v

How to set up the TP-Link VX420-G2h small business modem (with optional 4G backup) on any nbn technology, extend its Wi-Fi with Aginet mesh, and use bridge mode.

The TP-Link VX420-G2h is our small business modem router. It's a Wi-Fi 6 gateway with a built-in VDSL modem, so it works on every nbn technology type, and it has a SIM slot for optional 4G backup that keeps your business online if the nbn drops out. The VX420-G2v is a similar model without the 4G backup, and sets up the same way.

**Bought your VX420-G2h from Lightning IP?** It arrives pre-configured for your service. Just connect it to your nbn equipment (or your phone socket on FTTN or FTTB) and switch it on. You don't need to follow the setup steps below.

Use this guide if your modem came from another provider, was bought elsewhere, or has been factory reset. If it came from another provider, factory reset it before you start by holding the **Reset** button for about 10 seconds.

## Before you start

Check which nbn technology your address uses, then follow the matching section below. These are the settings our network needs:

| Setting | What to choose |
|---|---|
| Connection type | Dynamic IP (sometimes called IPoE, DHCP or Automatic) |
| VLAN / VLAN ID | Off (untagged) |
| Username and password | Not needed |

If your modem is already set up for PPPoE from a previous provider, you can leave it that way. We accept PPPoE with any username and password. Just make sure the VLAN setting is turned off.

## Logging in to your modem

1. **Connect a device** - Join the modem's Wi-Fi using the details on the label, or plug a computer into a LAN port.
2. **Open the setup page** - In a web browser, go to **http://tplinkmodem.net** or **192.168.1.1**.
3. **Sign in** - Create an admin password when prompted, or use the password on the label.

## Setting up on FTTN or FTTB

1. **Connect to the phone socket** - Plug the phone cable into the **DSL** port on the modem and the other end into your wall phone socket. Don't use any line filters or splitters.
2. **Power on and log in** - Switch the modem on and log in as described above.
3. **Start Quick Setup** - Click **Quick Setup** if it doesn't open automatically.
4. **Set your region** - Choose **Australia** and your time zone.
5. **Choose your provider** - Select **Other** from the ISP list.
6. **Enter the internet settings** - Tick **VDSL**. Leave **VLAN ID** unticked and set the connection type to **Dynamic IP**.
7. **Finish setup** - Save your Wi-Fi settings. Allow up to 10 minutes for the **DSL** light to go solid, followed by the **Internet** light.

## Setting up on FTTP, HFC, FTTC or Fixed Wireless

1. **Connect to your nbn equipment** - Run an ethernet cable from the modem's ethernet **WAN** port to your nbn equipment: port **UNI-D1** on an FTTP or Fixed Wireless Connection Box, the ethernet port on an HFC Connection Box, or the port labelled **Gateway** on an FTTC Connection Device.
2. **Power on and log in** - Switch the modem on and log in as described above.
3. **Run Quick Setup** - Set your region to **Australia** and choose **Other** from the ISP list.
4. **Enter the internet settings** - Leave **VDSL** unticked so the modem uses its ethernet WAN port. Leave **VLAN ID** unticked and set the connection type to **Dynamic IP**.
5. **Finish setup** - Save your Wi-Fi settings and wait a few minutes for the **Internet** light to turn on.

## 4G backup (optional)

4G backup is an optional extra on the VX420-G2h. When it's set up, the modem switches to the mobile network automatically if your nbn connection drops, and switches back when the nbn returns. Your nbn connection works without it.

If you'd like to add 4G backup to your service, get in touch and we'll help you get it set up.

## Extending your Wi-Fi with Aginet mesh

If the VX420-G2h's Wi-Fi doesn't reach every part of your premises, you can add TP-Link Aginet mesh units (the **HX510**, **HX716 Pro** or **HB210 Pro**). They join the VX420-G2h to create one Wi-Fi network across your home or office, with the same name and password everywhere. This works on every nbn technology, including FTTN and FTTB.

Because the VX420-G2h stays in charge of your connection, 4G backup keeps working across the whole mesh network, so it's the best way to extend coverage without losing backup.

1. **Make sure the VX420-G2h is online** - Set it up using the steps above and check the **Internet** light is on.
2. **Open the Aginet app** - Join your phone to the VX420-G2h's Wi-Fi, open the **TP-Link Aginet** app and log in. The app will find your modem; if it's the first time, set a device password.
3. **Add a mesh unit** - Tap **+** and choose to add a mesh device, then select your model.
4. **Power on the mesh unit** - Place the mesh unit near the VX420-G2h for setup, plug it into power and wait until the light flashes blue. Follow the prompts in the app to pair it.
5. **Move it into place** - Once paired, move the mesh unit to where you need better coverage, ideally within one or two rooms of the modem. Its light should turn solid when it has a good connection.
6. **Add any extra units** - Repeat for each extra mesh unit.

For the fastest, most reliable connection, run an ethernet cable from a LAN port on the VX420-G2h to the **WAN/LAN** port on the mesh unit. See our [Aginet mesh setup guide](/help/internet/setup-tp-link-aginet-mesh) for more detail.

## Using bridge mode with your own router (FTTN and FTTB)

On FTTN or FTTB you can set the modem to bridge mode so it acts only as a VDSL modem, and your own router or network equipment handles the connection and Wi-Fi. If you just want better coverage, adding Aginet mesh (above) is simpler and keeps 4G backup working.

Bridge mode is only needed on FTTN and FTTB. On other technologies, plug your own router straight into the nbn equipment instead.

1. **Connect with a cable** - Plug a computer into a LAN port on the modem and log in.
2. **Open the internet settings** - Go to **Advanced** > **Network** > **Internet**.
3. **Remove the current connection** - Delete the existing VDSL internet connection.
4. **Add a bridge connection** - Click **Add**. Set **Service Type** to **Internet**, **DSL Modulation Type** to **VDSL** and **Internet Connection Type** to **Bridge**. Leave VLAN turned off, then click **Save**.
5. **Connect your router** - Run an ethernet cable from a LAN port on the modem to the WAN (internet) port on your own router.
6. **Set up your router** - Set your router's internet connection type to **Dynamic IP** with VLAN turned off.
7. **Turn off the modem's Wi-Fi (optional)** - Press the **Wi-Fi** button so the modem doesn't compete with your router's Wi-Fi.

In bridge mode, 4G backup won't work and Aginet mesh units can't pair with the modem, because your own router is now managing the connection. If 4G backup matters to your business, keep the VX420-G2h as your main router instead. To undo bridge mode, factory reset the modem and follow the FTTN or FTTB steps above.

## If it doesn't connect

- **DSL light flashing or off (FTTN/FTTB)** - Check the phone cable, remove any filters or splitters, and try another phone socket.
- **Internet light off** - Check the connection type is **Dynamic IP** and that VLAN is turned off.
- **Mesh unit won't pair** - Move it closer to the modem, make sure the modem is online and not in bridge mode, and try adding it again in the Aginet app.
- **Still no luck** - Restart the modem properly and follow our no internet connection troubleshooting guide, or get in touch.
