---
title: "Setting up your TP-Link Archer VR1600v, VR400 or VR300"
description: "How to set up an older TP-Link Archer VR-series modem on FTTN/FTTB or Ethernet WAN nbn, and how to put it in bridge mode."
url: "https://www.lightningip.com.au/help/internet/setup-tp-link-archer-vr-series"
canonical: "https://www.lightningip.com.au/help/internet/setup-tp-link-archer-vr-series"
updated: "2026-11-16"
---

# Setting up your TP-Link Archer VR1600v, VR400 or VR300

How to set up an older TP-Link Archer VR-series modem on FTTN/FTTB or Ethernet WAN nbn, and how to put it in bridge mode.

The TP-Link Archer VR1600v, VR400 and VR300 are older Wi-Fi 5 modem routers with a built-in VDSL modem. Many were supplied by Optus and other providers, and they share the same setup screens. Use this guide if you're bringing one across to Lightning IP.

These modems are fine for everyday use on slower plans, but their Wi-Fi 5 hardware can hold back faster plans (nbn 250 and above). If you're on a faster plan, a newer modem will usually give you better results.

## Before you start

Check which nbn technology your address uses, then follow the matching section below. These are the settings our network needs:

| Setting | What to choose |
|---|---|
| Connection type | Dynamic IP (sometimes called IPoE, DHCP or Automatic) |
| VLAN / VLAN ID | Off (untagged) |
| Username and password | Not needed |

If your modem is already set up for PPPoE from a previous provider, you can leave it that way. We accept PPPoE with any username and password. Just make sure the VLAN setting is turned off.

## Logging in to your modem

1. **Connect a device** - Join the modem's Wi-Fi using the details on the label, or plug a computer into a LAN port.
2. **Open the setup page** - In a web browser, go to **http://tplinkmodem.net** or **192.168.1.1**.
3. **Sign in** - Create an admin password when prompted, or use the password on the label.

## Setting up on FTTN or FTTB

1. **Connect to the phone socket** - Plug the phone cable into the grey **DSL** port on the modem and the other end into your wall phone socket. Don't use any line filters or splitters.
2. **Power on and log in** - Switch the modem on and log in as described above.
3. **Check the operation mode** - Go to **Advanced** > **Operation Mode** and make sure **DSL Modem Router Mode** is selected.
4. **Start Quick Setup** - Click **Quick Setup**, choose **Australia** and your time zone, and select **Other** from the ISP list.
5. **Enter the internet settings** - Choose **VDSL**. Leave **VLAN ID** unticked and set the connection type to **Dynamic IP**.
6. **Finish setup** - Save your Wi-Fi settings. Allow up to 10 minutes for the **DSL** light to go solid, followed by the **Internet** light.

## Setting up on FTTP, HFC, FTTC or Fixed Wireless

1. **Connect to your nbn equipment** - Run an ethernet cable from the yellow **LAN4/WAN** port on the modem to your nbn equipment: port **UNI-D1** on an FTTP or Fixed Wireless Connection Box, the ethernet port on an HFC Connection Box, or the port labelled **Gateway** on an FTTC Connection Device.
2. **Power on and log in** - Switch the modem on and log in as described above.
3. **Change the operation mode** - Go to **Advanced** > **Operation Mode**, select **Wireless Router Mode** and click **Save**. The modem will restart.
4. **Set the internet connection** - Log back in, go to **Advanced** > **Network** > **Internet**, and set the connection type to **Dynamic IP** with VLAN turned off. Click **Save**.
5. **Check the connection** - Wait a few minutes for the **Internet** light to turn on.

## Using bridge mode with your own router (FTTN and FTTB)

On FTTN or FTTB you can set the modem to bridge mode so it acts only as a VDSL modem, and your own router or mesh system handles the connection and Wi-Fi.

Bridge mode is only needed on FTTN and FTTB. On other technologies, plug your own router straight into the nbn equipment instead.

1. **Connect with a cable** - Plug a computer into a LAN port on the modem and log in. Make sure the modem is in **DSL Modem Router Mode**.
2. **Open the internet settings** - Go to **Advanced** > **Network** > **Internet**.
3. **Remove the current connection** - Delete the existing VDSL internet connection.
4. **Add a bridge connection** - Click **Add**. Set **DSL Modulation Type** to **VDSL** and **Internet Connection Type** to **Bridge**. Leave VLAN turned off, then click **Save**.
5. **Connect your router** - Run an ethernet cable from a LAN port on the modem to the WAN (internet) port on your own router.
6. **Set up your router** - Set your router's internet connection type to **Dynamic IP** with VLAN turned off.
7. **Turn off the modem's Wi-Fi (optional)** - Use the **Wi-Fi** button or switch so the modem doesn't compete with your router's Wi-Fi.

To undo bridge mode, factory reset the modem and follow the FTTN or FTTB steps above.

## If it doesn't connect

- **DSL light flashing or off (FTTN/FTTB)** - Check the phone cable, remove any filters or splitters, and try another phone socket.
- **Internet light off** - Check the connection type is **Dynamic IP**, that VLAN is turned off, and that the operation mode matches your technology.
- **Still no luck** - Restart the modem properly and follow our no internet connection troubleshooting guide, or get in touch.
