---
title: "Setting up an Optus Ultra WiFi Modem"
description: "How to factory reset and connect an Optus Ultra WiFi Modem to your Lightning IP nbn service."
url: "https://www.lightningip.com.au/help/internet/setup-optus-ultra-wifi-modem"
canonical: "https://www.lightningip.com.au/help/internet/setup-optus-ultra-wifi-modem"
updated: "2026-11-16"
---

# Setting up an Optus Ultra WiFi Modem

How to factory reset and connect an Optus Ultra WiFi Modem to your Lightning IP nbn service.

Optus Ultra WiFi Modems work with Lightning IP in their default settings. Once the modem is back to factory settings, it connects to our network automatically, so there's nothing to type in.

We recommend factory resetting your Optus modem before you connect it. This clears any Optus-specific settings and puts it back into the default state that works on our network.

## What won't work on our network

Your Optus modem will give you internet and Wi-Fi, but some Optus features rely on an Optus service and won't work once you've switched:

- **4G backup** - This uses an Optus SIM and service.
- **Optus home phone** - Phones plugged into the modem won't work. If you have a Lightning IP phone service, get in touch and we'll let you know what's needed.

## Factory resetting your Optus modem

1. **Leave it switched on** - Keep the modem powered on.
2. **Press and hold Reset** - Using a paper clip, press and hold the small **Reset** button on the back for about 10 seconds, until the lights flash.
3. **Wait for it to restart** - Leave it for a few minutes while it restarts with factory settings.

## Setting up on FTTN or FTTB

This section only applies if your Optus modem has a grey, phone-style **DSL** port on the back. If it doesn't, it can only be used on FTTP, HFC, FTTC or Fixed Wireless.

1. **Factory reset the modem** - Follow the steps above.
2. **Connect to the phone socket** - Plug the phone cable into the **DSL** port on the modem and the other end into your wall phone socket. Don't use any line filters or splitters.
3. **Power on and wait** - Switch the modem on and allow up to 15 minutes for it to connect.
4. **Connect your devices** - Join the Wi-Fi using the name and password on the label on the modem.

## Setting up on FTTP, HFC, FTTC or Fixed Wireless

1. **Factory reset the modem** - Follow the steps above.
2. **Connect to your nbn equipment** - Run an ethernet cable from the modem's **WAN** port to your nbn equipment: port **UNI-D1** on an FTTP or Fixed Wireless Connection Box, the ethernet port on an HFC Connection Box, or the port labelled **Gateway** on an FTTC Connection Device.
3. **Power on and wait** - Switch the modem on and allow up to 15 minutes for it to connect.
4. **Connect your devices** - Join the Wi-Fi using the name and password on the label on the modem.

## Using your own router

Optus modems don't have a simple bridge mode, so we don't recommend using one as a modem for a separate router on FTTN or FTTB. If you want to use your own router or mesh system on FTTN or FTTB, one of the modems in our setup guides that supports bridge mode is the better choice.

On FTTP, HFC, FTTC and Fixed Wireless you don't need the Optus modem at all. Plug your own router straight into the nbn equipment instead.

## If it doesn't connect

- **DSL light flashing or off (FTTN/FTTB)** - Check the phone cable, remove any filters or splitters, and try another phone socket.
- **No internet after 15 minutes** - Factory reset the modem again and leave it to connect without changing any settings.
- **Still no luck** - Restart the modem properly and follow our no internet connection troubleshooting guide, or get in touch.
