---
title: "Setting up an older NetComm modem (NF18ACV, NF17ACV or NF10WV)"
description: "How to set up an older NetComm NF18ACV, NF17ACV or NF10WV on FTTN/FTTB or Ethernet WAN nbn, and how to put it in bridge mode."
url: "https://www.lightningip.com.au/help/internet/setup-netcomm-nf18acv-nf17acv-nf10wv"
canonical: "https://www.lightningip.com.au/help/internet/setup-netcomm-nf18acv-nf17acv-nf10wv"
updated: "2026-11-16"
---

# Setting up an older NetComm modem (NF18ACV, NF17ACV or NF10WV)

How to set up an older NetComm NF18ACV, NF17ACV or NF10WV on FTTN/FTTB or Ethernet WAN nbn, and how to put it in bridge mode.

The NetComm NF18ACV, NF17ACV and NF10WV are older modem routers with a built-in VDSL modem. They were supplied by many providers and share very similar setup screens. Use this guide if you're bringing one across to Lightning IP.

These modems are fine for everyday use on slower plans, but their older Wi-Fi hardware can hold back faster plans (nbn 100 and above). If you're on a faster plan, a newer modem will usually give you better results.

## Before you start

Check which nbn technology your address uses, then follow the matching section below. These are the settings our network needs:

| Setting | What to choose |
|---|---|
| Connection type | Dynamic IP (sometimes called IPoE, DHCP or Automatic) |
| VLAN / VLAN ID | Off (untagged), or leave the VLAN field blank |
| Username and password | Not needed |

Many of these modems were set up for PPPoE by a previous provider. You can leave that in place, as we accept PPPoE with any username and password. Just make sure the VLAN setting is turned off, since some providers used VLAN 100.

## Logging in to your modem

1. **Connect a computer** - Plug a computer into a yellow LAN port (labelled **Eth. 1** on some models) with an ethernet cable, or join the modem's Wi-Fi.
2. **Open the setup page** - In a web browser, go to **192.168.20.1**.
3. **Sign in** - Enter **admin** as the username. The password is usually **admin** or the password printed on the label.

## Setting up on FTTN or FTTB

1. **Connect to the phone socket** - Plug the phone cable into the grey **DSL** port on the modem and the other end into your wall phone socket. Don't use any line filters or splitters.
2. **Log in** - Switch the modem on and log in as described above.
3. **Open Basic Settings** - Click **Basic Settings** in the left-hand menu.
4. **Choose the connection** - Select **VDSL** as the WAN connection type, then click **Next**.
5. **Choose the connection type** - Select **Dynamic IP** (or **IPoE**). If you're asked about a VLAN tag, leave it turned off. Click **Next**.
6. **Finish** - Click **Finish** or **Save**. Allow up to 10 minutes for the **DSL** light to go solid, followed by the **Internet** light.

## Setting up on FTTP, HFC, FTTC or Fixed Wireless

1. **Connect to your nbn equipment** - Run an ethernet cable from the modem's **WAN** port to your nbn equipment: port **UNI-D1** on an FTTP or Fixed Wireless Connection Box, the ethernet port on an HFC Connection Box, or the port labelled **Gateway** on an FTTC Connection Device.
2. **Log in** - Switch the modem on and log in as described above.
3. **Open Basic Settings** - Click **Basic Settings** in the left-hand menu.
4. **Choose the connection** - Select **Ethernet WAN** as the WAN connection type, then click **Next**.
5. **Choose the connection type** - Select **Dynamic IP** (or **IPoE**), leave VLAN turned off, and click **Next**.
6. **Finish** - Click **Finish** or **Save**. The **Internet** light should turn on within a few minutes.

## Using bridge mode with your own router (FTTN and FTTB)

On FTTN or FTTB you can set the modem to bridge mode so it acts only as a VDSL modem, and your own router or mesh system handles the connection and Wi-Fi.

Bridge mode is only needed on FTTN and FTTB. On other technologies, plug your own router straight into the nbn equipment instead.

1. **Connect with a cable** - Plug a computer into a yellow LAN port and log in.
2. **Open Basic Settings** - Click **Basic Settings** and select **VDSL** as the WAN connection type.
3. **Choose Bridge** - Select **Bridge** (sometimes shown as **Bridging**) as the connection type. Leave VLAN turned off and save.
4. **Turn off the modem's Wi-Fi** - In the wireless settings, turn off Wi-Fi so it doesn't compete with your router's.
5. **Connect your router** - Run an ethernet cable from a LAN port on the modem to the WAN (internet) port on your own router.
6. **Set up your router** - Set your router's internet connection type to **Dynamic IP** with VLAN turned off.

To undo bridge mode, factory reset the modem using the reset button, then follow the FTTN or FTTB steps above.

## If it doesn't connect

- **DSL light flashing or off (FTTN/FTTB)** - Check the phone cable, remove any filters or splitters, and try another phone socket.
- **Internet light off** - Check the connection type is **Dynamic IP** and VLAN is turned off.
- **Firmware** - Older NetComm modems may need a firmware update to work reliably. You'll find this under **Management** > **Update Firmware**, using the latest file from NetComm's support site.
- **Still no luck** - Restart the modem properly and follow our no internet connection troubleshooting guide, or get in touch.
